week 35-2018

Markenburg International Foods Corporation Philippines received a DS1400 Vacuum System ATEX Zone 22 on 28/09/2018.

The DS1400 mobile vacuum unit is combined with  a 110L Pre-Separator System with bag suction. The purpose of this vacuum unit is to generally clean corn starch powder in the marshmallow production line and replacing the wet cleaning process.

Mr. Alfred de Guzman (Middle), Plant Manager says that our Ruwac vacuum system has decreased their cleaning time of the production area, increased cleaning efficiency & helped his operators from being exposed to corn starch powders.

Week 33-2018

Due to the quantity of Bentonite powders, a very cost-efficient solution was installed to serve two platforms. One DS1400M mobile vacuum with control system combined with a 110L Pre-separator, connected to a short piping system and end cap connection points for the to cover 2nd and 3rd floor of the production tower. Customer can also use the same unit for cleaning ground floor around the tower.

Week 27-2018

Another Ruwac deduster for the suction of PCB dust handed over to Mr Nicolas of Getech Automation Pte Ltd Singapore

Week 25-2018

Our OEM customer IWK (Thailand) Limited., a manufacturer of packaging and filling machines, received the Ruwac Compact-Vac DA0040 De-Duster on 22nd June 2018.

The purpose of this vacuum unit is to dedust general dust from tubes before filling its contents in order to comply with GMP regulations.

Khun Prasert, Production Manager of IWK says that the Compact-Vac is very practical in operation as tubes can vary in sizes and shapes which requires air flow regulation possibility. Current standard vacuums used did not have that feature.

Week 10-2018

At Saigon Exhibition & Convention Center in Ho Chi Minh, Vietnam from the 20th – 22nd March 2018, Booth#B11

Week 09 - 2018

Our OEM customer Trumpf Ltd., a manufacturer of 3D laser sintering machines, received a NA7-11H wet-separator on 27th February 2018.

The purpose of this vacuum unit is to generally clean highly explosive aluminum and titanium powders from 3D laser sintering machines, which have a minimum ignition energy of lower than 1mJ.

Trumpf Ltd. says that the NA7-11H is a necessary asset when cleaning their line of 3D laser sintering machines in order to comply with special regulations regarding the handling of titanium powder and other reactive powders.

In this particular order regarding the NA7-11H wet-separator, the end user is Mahidol University whereas the institute will teach the students on how to clean and properly dispose of highly reactive powders such as titanium and aluminum powders.

Week 44 - 2017

The DA1300 Dust-Ex Zone 22 is combined with  a 110L Pre-separator/Filter System whereas 2 operation modes can be switched manually by a ball valve:

1. Cleaning of PE pellets from Big-Bag unloading station with Pre-Separator
2. Cleaning of sticky nylon powders from Film Printing line with Pre-Filter

The purpose of the DA1300 Vacuum Unit is to generally clean both areas mentioned above with 1 vacuum unit

Thai Polyamide Team says that our Ruwac vacuum unit has eliminated electrocutions from cleaning due to our vacuum units’ full conductivity system & increased cleaning efficiency

Week 35 - 2017

Mr Jens Huhn and Mr Musab Mohd Saat of Ruwac SDN Malaysia handed over a RUWAC S 24 heavy duty vacuum truck to Mr Rozlan Daud and his operation team at “CIMA’s” cement mill in Bahau – Malaysia.
The RUWAC S 24 vacuum system is mounted on a Nissan 2 axle heavy duty truck with full roadgoing permit.
The vacuum system is equipped with a SIBILIA pump and its own DEUTZ Diesel engine , capable to vacuum any dry spillage material occurring in a cement plant at a capacity of up to 20 tons / h.
The unit is equipped with all safety equipment as well as connectivity to a central system vacuum pipeline.
RUWAC Malaysia in cooperation with DEUTZ Malaysia will take care for continuous operator training and service.

Week 32 - 2017

Mr Jens Huhn handed over the first RUWAC DAV deduster for continuous suction of trimmings to IWK Thailand. IWK is the world leading manufacturer of turn key tube filling and packing lines. The decision for RUWAC was made after extensive testing at IWK's production plant in Thailand.

Week 23 - 2017

Saint-Gobain Abrasives (TH) Co.,Ltd. received a DS2 Wet-Separator Vacuum System on June 2017.

The DS2 Wet-Separator Vacuum System is connected to 4 Suction Points whereas 1 suction point is operated at the same time. The purpose of this Vacuum System is to de-dust grinding sparks from their QC Testing Room.

Khun Darunee (Right), EHS Specialist said that our Ruwac vacuum system is essential to their operation due to compliance with ATEX regulations as well as extreme worker protection.